Your Screen Extender Just Arrived: The Ten-Minute Check Before You Put the Box in the Loft

The box arrives, the panels work, and it goes straight into daily use. Entirely reasonable, and it is how most people end up discovering a fault in month four, when the return window has closed and the conversation is harder. Ten minutes on day one avoids nearly all of that. Here is what to actually look at. Last updated: November 2026. One: all panels light up, on the cable you will actually use Sounds obvious. The reason it is first is that multi-panel setups sometimes behave differently depending on which port you use and whether external power is connected. Plug it in the way you intend to use it every day. If you plan to run it from the laptop alone, test that. If you plan to run it with its own power supply, test that too. A setup that works on mains and drops a panel on laptop power alone is something to know now. If a panel does not appear, before assuming a fault: check Settings, System, Display on Windows or System Settings, Displays on a Mac and press Detect. Our troubleshooting guide covers the usual causes in order. Two: dead and stuck pixels The check everyone has heard of and few do properly. Put each panel full-screen on a plain colour and look closely. Do it on black, white, red, green and blue in turn. A black image reveals stuck-on pixels as bright dots. A white image reveals dead pixels as dark dots. Colour screens catch sub-pixel faults that both miss. The easiest way is a full-screen browser window with the background set to each colour, dragged onto each panel in turn. What is normal: manufacturers work to a pixel policy, and one or two sub-pixel defects on a large panel is usually within spec for the industry. We would rather you tell us and we take a view than you find it in April. What is not: a cluster, anything in the middle third of the screen, or a line. Three: backlight bleed and clouding Put a panel on a full black image in a dark room. Some light leakage at the very edges is normal on an edge-lit panel, and every portable screen is edge-lit. What you are looking for is a bright patch or a visible corner glow that is obvious at normal brightness, not something only detectable in a blacked-out room at full brightness with your face against the screen. Compare the panels against each other. They came from the same batch and should look similar. One noticeably worse than its siblings is worth raising. Four: the hinges The most common long-term complaint about multi-panel extenders, and almost always detectable immediately. Fold each panel out to a working angle and leave it. Then nudge the desk. Then fold them in and out ten times. A panel that will not hold position on day one will be worse in six months, not better. Hinges loosen with use, they do not tighten. If a wing creeps shut while you are looking at it, say so now. Also check the panels sit level with each other when extended. A panel that hangs visibly lower is irritating in a way that compounds over months. Five: the mounting on your actual laptop Extenders attach with magnets or a clip onto the lid. Lid thicknesses and finishes vary, and so does how well a given extender grips. Open and close your laptop a few times with the extender mounted and folded. Carry it across the room. Check it is not putting a point load on the lid, and that the laptop is not now so back-heavy that it tips when you open it one-handed. If your laptop is unusually thin, unusually thick, or has an unusual lid shape, this is the check that matters most. Six: resolution and refresh per panel Open display settings and confirm each panel is running at the resolution you paid for, not a fallback. It is common for a laptop driving three or four panels to default one of them to something lower, particularly on older integrated graphics. Usually fixable in settings. Occasionally it is a genuine bandwidth limit, which is covered in our Windows compatibility guide. Also check the refresh rate. 60Hz is standard. A panel sitting at 30Hz will feel subtly wrong when you move the mouse across it, and most people notice the feeling long before they work out the cause. Seven: a day of real work before you decide The checks above catch defects. This one catches fit. Use it for one full working day in the arrangement you intend, and pay attention to: Neck and eye comfort. Laptop-mounted panels sit at laptop height. If your neck complains by three o'clock, read posture and screen height before you conclude the product is wrong. Whether you used all the panels. People who buy quad and use two have bought the wrong thing, and it is better to find that out in week one. Our dual versus triple versus quad guide is worth a re-read at this point. Whether it actually folds away as conveniently as you need. If the daily setup is annoying, you will stop using it. Keep the box, for a bit Not forever. Until you have done the above and worked a normal week. It makes any conversation about a return or a replacement straightforward rather than a negotiation about packaging, and it costs you a week of cupboard space. If something is not right Tell us early and tell us specifically. "The left panel is dimmer than the other two on a white background" is something we can act on immediately. "It seems a bit off" in March is much harder for everybody. Get in touch with the model, what you are seeing, and ideally a photo. We would far rather sort it in week one.